Page Comparison

...

1. Before you publish a bill, always start with a clean bill  

   1. You should have done this already when preparing the As Introduced version but double check there are no ‘bad’ document checks, remove all comments and delete any jrefs 

2. If you want to make updates to a bill version in advance of applying amendments (e.g., printing points from OPC) duplicate the published bill version 

   1. You need to duplicate this version as it will include page-line information needed for auto-apply to work 

3. Before applying amendments, always start with a clean set of amendments 

   1. To check if the amendments are clean, select them using check boxes on the ‘Amendment Manager’ tab before applying them and open them in the Editor (Amendment Actions > Create temporary list) 

      1. Check Document Checks right-hand panel in the Editor to double check there are no mandatory checks that need addressing

      2. Remove any comments from the ‘Review’ right-hand panel 

4. [COMMONS ONLY] Update new clause and new schedule amendments with location information 

   1. This is particularly useful if there are a large number of new clause and/or new schedule amendments as it will save you time when dragging them to the correct location in your bill after they have been applied 

   2. Open the Amendment Information right-hand panel for each new clause amendment and update the ‘Location’ box with “before” or “after”; and update the ‘Provision’ box with the appropriate provision number in the format “sec_22” for sections (clauses) and “sch_3” for schedules.

...

1. From the Amendment Manager, select the amendments you want auto-applied and run Amendment Actions > Apply Amendments.   

   1. Consider using filters to make it easier to 'select all' amendments to apply e.g., filter by Member 

   2. You can apply amendments to the same bill version in batches 

   3. Large bills containing lots of amendments can sometimes take a while to auto-apply (~3 mins) 

   4. Create new bill version if you have not already created an as amended version 

2. Accept all the applied amendments displayed as tracked changes  

   1. If it is a large bill, use Actions > https://lawmaker.scrollhelp.site/help/live/editing-a-portion-of- Edit portion of document mode 

   2. Click on the Accept All Amendments button at the top of Inline Amendments r-h panel 

   3. Check for any new Document Check messages (ignore advisory or x-ref doc check errors for now as they will be dealt with as part of ‘Finalise Document’ stage) 

3. In the Editor, move to the Review r-h panel where auto-apply warning messages are posted.    

   1. Some messages warn you that the amendments were applied but need checking e.g. if there was more than one paragraph being inserted by different amendments in the same place, the warning message is asking you to check the sort order;

   2. Some messages warn you that a certain amendment couldn’t be applied; in this case, open up the specified amendment in a temporary list and check for any obvious mistakes e.g. page-line information or whitespace at the end of the instruction if it’s inserting new provisions. If you cannot fix the amendment, right-click in the quoted structure and select “Copy content of quoted structure” and manually paste it in the correct location.

   3. Delete the warnings that you’ve dealt with as you go so you can keep track of which issues you have resolved.

4. If you need to manually apply amendments: 

   1. Open the PDF of the published bill to help work out location of insertions/leave outs 

   2. Select the amendment(s) that could not be applied on the Amendment Manager and open them in a temporary list 

   3. Display the list side-by-side with your bill (use the Windows button on your keyboard with the left arrow to divide your monitor view in half) as in this example below: 

   4. 

   5. To copy provisions inside a quoted structure:  

      1. Place cursor inside the quoted structure of the amendment 

      2. Right-click and select "copy content of quoted structure" 

      3. Place cursor in the bill where you would like to paste the content and use Ctrl + V.    

      4. Check for locked nums when you do this, they may need manually removing (right-mouse-click > Lock/unlock num)  

   6. To copy text from the amendment instruction:  

      1. Highlight and copy the text within the quotation marks 

      2. Place cursor in the bill where you would like to paste the content and use Ctrl + V 

      3. To insert new clauses which contain grouping levels, e.g., a Part you will need to copy the content of the quoted structure and paste it directly into your document in the correct location. 

...